Certifications

Vancomp International

NSF/ANSI 61 (N-5835)

Drinking Water System Components & Health Effects

  • Identification: Each product shall be permanently and legibly marked with the manufacturer name or trademark. The product may also be marked with the standard designation "NSF/ANSI 61".
  • Characteristics: Materials or products that come into contact with drinking water and/or drinking water treatment chemicals. Products and materials may include process media, protective materials, joining and sealing materials, pipes and related products, mechanical devices used with treatment/transmission/distribution systems, and mechanical plumbing devices. To be installed in accordance with the manufacturer's instruction.
  • Products listed on this certificate have been tested by an IAPMO R&T recognized laboratory. This recognition has been granted based upon the laboratory's compliance to the applicable requirements of ISO/IEC 17025.

CUPC/UPC/ASME/CSA (5727)

Plumbing Fixture Fittings

  • Identification: Each fitting shall bear permanent legible markings to identify the manufacturer. This marking shall be the trade name, trademark, or other mark known to identify the manufacturer. The product shall also bear all other markings required by the standard. The marking shall be located where it can be readily seen after installation is complete. The product shall also bear the cUPC certification mark.
  • Characteristics: Plumbing fixture fittings, other terminal fittings and supply stops to be installed in accordance with the manufacturer instructions and the requirements of the latest edition of the Uniform Plumbing Code. Fittings may include kitchen, lavatory, bath & shower and lawn faucets.
  • Products listed on this certificate have been tested by an IAPMO R&T recognized laboratory. This recognition has been granted based upon the laboratory's compliance to the applicable requirements of ISO/IEC 17025.
  • Products are in compliance with the following code(s):
    • Uniform Plumbing Code (UPC)
    • National Plumbing Code of Canada (CSA)
  • Products are in compliance with the following standard(s):
    • ASME A112.18.1-2011/CSA B125.1-11 including Update No. 1 dated November 2011

AB-1953

California Lead Plumbing Law: Devices and Components

  • Identification: Each product shall bear permanent and legible markings to identify the manufacturer. This marking shall be the trade name, trademark, or other mark known to identify the manufacturer. The product and/or product packaging may also bear the term "Lead Plumbing Law", "Complies with Lead Plumbing Law", or "Low-Lead" above or in close proximity to the appropriate IAPMO R&T certification mark, or the term "Certified by IAPMO R&T". The product packaging may also bear a grey dot, a check mark with circle, or any other home centers marking requirements.
  • Characteristics: Products listed below are to be installed in accordance with the manufacturer's instruction. These products have been verified with weighted average lead content <=0.25%; Solder and flux lead content <=0.2%.
  • Products listed on this certificate have been tested by an IAPMO R&T recognized laboratory. This recognition has been granted based upon the laboratory's compliance to the applicable requirements of ISO/IEC 17025.
  • Products are in compliance with the following standard(s):
    • Section 116875 of the California Health & Safety Code
    • NSF/ANSI 372-2011
    • Vermont Lead Reduction Law (Vermont Act 193)
    • Maryland Lead Reduction Law (Maryland House Bill HB.372)

EPA WaterSense

EPA WaterSense High Efficiency Lavatory Faucets

  • Identification: Each product shall be marked per the marking requirements of the applicable performance standard. The product or packaging shall bear the EPA WaterSense logo.
  • Characteristics: Lavatory faucets manufactured in compliance with the applicable requirements of the EPA WaterSense High Efficiency Lavatory Faucet Specification. To be installed in accordance with the manufacturer's installation instructions.
  • Products comply with the applicable sections of the latest edition of the Uniform Plumbing Code® and the International Plumbing Code®. Manufactured in compliance with EPA WaterSense High Efficiency Lavatory Faucet Specification (version 1.0, 10-1-07 edition).
  • Products listed on this certificate have been tested by an IAPMO R&T recognized laboratory. This recognition has been granted based upon the laboratory’s compliance to the applicable requirements of ISO/IEC 17025.